Cue Builder Maintenance, Supplies and Tools

These are the finest maintenance kits available and they offer versatility. These are best used when doing shaft and butt repairs when you need the work piece held precisely and firmly in your chuck. Each tool contains the male and female end. The barrel (without the threads) measure approximately 3" and the barrel is approximately .600" is diameter and made of high grade aluminum.

Our prices are the same for all models. You won't find these anywhere at prices this low. Only because of our huge buying power can we make these available at these ridiculously low, low prices.

We are offering the finest and most populate size dyed sycamore available in 1.350" X 11.5" X .6mm thick. These veneers strips are high quality and very consistent. You can purchase veneers strips for less but compare quality with price. Our dyed sycamore is about twice the cost of lower grade dyed poplar veneers. The colors are vibrant, consistent and have withstood the test of time. We offer 11 different colors: black, burgundy, dark blue, green, light blue, natural, orange, purple, red and yellow.

For your edification, the .6mm are .75 each. The .6mm are great for any application especially when doing 4, 5, 6, or 8 points and if you want 3, 4 or even 5 veneer colors.

We no longer carry the .9mm veneers as they are no longer popular since most cue makers and buyers are trending towards finer and more detailed craftsmanship.

We have four styles as pictured. We are selling these individually and groups of 10 and 20. Choose whatever style you like

Please click on picture for the specs of the bumpers.

A) Beveled Top (which requires an allen screw)

B) Threaded Stem Type - 3/8 x 16

C) Large Push In Flat South West Style

D) Push In Flat South West Style

Check out our new SouthWest Style Joint Pins.

Fiber ferrule pads are used between the ferrule and the tip. Some believe this protects the ferrule while others believe it enhances the 'hit'. Both are actually correct. It depends which camp you're in.

We recommend using these especially with Genuine Elephant Ivory Ferrules.

Each pad is .031" thick and 14mm diameter.

This is a 6 piece high speed steel 1/4" tool bit set and comes with:

1) Right Hand
2) Left Hand
3) Cut-Off Tool
4) Boring Bar
5) 45 Degree
6) Round Nose

This is without question the finest cue makers shaft sealant/stabilizer and final coat shaft sealer on the market today.

Speed Seal II Shaft Sealer & Stabilizer is sold in 16oz bottles and applies easily. And, it dries quickly too. Very quick!

For refinishing shafts: All you do is apply two coats back-to-back, sand (with 800) and wax. It's that quick!

For sealing shafts between cuts: Best to wipe on after the first cut and then again 2 cuts from final for lasting protection and stabilization. Add again at final stage when prepping the shaft for the actual sale.

When you're done you'll have a finish that is smooth as silk and will remain that way through all the abuse of playing.

Ever wonder how some cue makers get their shafts to glide like silk? Well, wonder no more!

Leading cue makers have been using this product for years with phenomenal results. You can too.

This is another fine product to burnish all leather; either wraps or tips. Can be used to burnish our Stack Leather Wrap, cue tips or any other stack or regular leather wrap. Our liquid burnisher can be used to burnish the sides of cue tips and it can burnish all leather wraps. It can also clean the surface dirt from your shaft and ferrule as well. A great product brought to you by CueComponents.

And the best thing - it is a free marketplace product without manufacturer pricing controls. Our price is distributor pricing so pick up a few!

This is 4 fluid ounces! Not 2 ounces like other products.

These are 100% genuine Micarta. They play great!

These are one of the finest ferrules money can buy. Try some and see for yourself. If you don't think these are the best Micarta ferrules, simply return them and we'll refund your original purchase price plus all shipping costs. They're the real deal.

Each ferrule is approximately .562 in diameter and 1.090" in length.

Cue Components Micarta is the finest composite based ferrule material available for custom cue makers. The hit is the same regardless which way you hold your cue. Micarta is strong, impact-resistant and bonds well with Cyanoacrylate and epoxy as well as wood glue. It machines, drills, taps and sands well. This micarta will polish to a beautiful high gloss soft yellowish finish. Unlike other ferrule materials, Micarta is not porous and will not absorb blue chalk. It produces a solid hit. If you try it once, you'll use it exclusively on all your cues. These can be used as capped or uncapped type ferrules.

Special Note: These are now available drilled and tapped (threaded). Our price is low so as to allow you the maximum savings.

For installing tips on these ferrules we highly recommend our Cyanoacrylate for tips.

These are high quality stainless steel and are 3/8 x 10 and 3" in length.
These are what we refer to as old reliable and a great choice for cue makers.

This quality carnauba cue wax is specifically formulated for billiard cues (without any harmful additives).

It's best used for finishing shafts as it provides an ultra smooth and glossy finish without all the drag associated with other waxes.

Try it as you will not be disappointed and you'll be back for more. You won't find this quality product for less!

These are the 1.7 ounce jars!!

This pool cue ferrule material is Genuine yellow Westinghouse Linen Micarta from many moons ago. This is a linen based micarta ferrule material (not a paper based micarta ferrule material). This linen based micarta is a strong ferrule material that will still generate a good amount of spin. These are a rare ferrule material so get them while you can. Strictly in limited supply. Pricing subject to change without notice.

The photo above shows raw solid Westinghouse Linen Micarta ferrule blanks in block form, square form, in round form, and a drilled and tapped raw micarta ferrule. And lastly, there is one finished and polished so you know what they will look like when installed (we do nice work, huh!). :-)

These are approximately .540" round x 1.060" in length. The squares have a slightly larger diameter.

Drilled and tapped are supplied in round form only. Squares cannot be supplied drilled and tapped.

High grade stainless steel 5/16-18 x 3" in length and widely used as joint screws in a variety of cues.

These are 6" Digital Calipers which are accurate to .0001. Metric and English digital display. Fluid-resistant stainless steel frame and precision ground jaws. Automatic on/off switch. Features include a thumb wheel for ease of use, zero set, lock, and inch/mm button.

We'll even include a 1.5V button cell battery. Order now and we will also include an extra battery at no additional charge!

There are knock-offs of this cutter out there which are imported from overseas. Ours is made in America. That's the difference in price. If you want to save then buy their cutter but if you want American quality and precision, then this is the cutter for you.

This tool is great for table top lathes such as Porper, Hightower and Unique (taper shaper and their CNC) as well as larger floor lathes and Align-Rite CNC machines. The diameter is 1.25" with a 1/4" shank; incredibly small but with the necessary power. Carbide Tipped!

This is made on a CNC machine and the blades are all in-line with one another. This is a 6 flute router bit for extreme accuracy, smooth cuts and less vibration. You'll get ultra smooth cuts on shafts and butts. The cut is so smooth that it appears as if the finished piece has been sanded and buffed! Exceptionally clean cuts. A must for the serious cue builder.

We use this 6 flute blade on our router when cutting shafts and butts with our 14" X 40" tapering lathe as well as other machines. This is a great cutter!

- Unsolicited Testimonial -

"I just used my new 6 fluted router blade. This blade is far superior to any other, it's hard to describe the results. The cut is much faster and smoother than anything I have ever used. I want to thank Cue Components for making such a great product available". CS Warsaw, MO

• Cleans While it Dries
• Cleans Without Chemicals
• Removes Wax Dust Without Scratching
• 80% Polyester, 20% Polymide
• 16" Square
• Pack of 4

Here is a dead center which can be used on a large metal lathe. It's long enough and the diameter is small to keep the work piece away from the headstock. The small diameter allows you to cut wood without worrying about the blade hitting the dead center.

The dead center is 5.5" long
The shank is .5"

These are similar to the 'Radial' pin but we're not allowed to use the word 'radial' as it is trademarked so we're using the word 'radius'. You can buy the 'radial' pin and pay more or you can buy our 'radius' and save money. We defy you to tell them apart. These are 3/8 x 3" stainless steel.

These are 5/16-14 x 3" in length. These are widely used in pool cues and exceptional quality stainless steel.